COLOURLAND PAINTS SDN. BHD

Sdn Bhd in relation to goods manufactured or marketed by it or their use or any application is given in good faith. However, any advice, recommendatio...

0 downloads 122 Views 384KB Size
COLOURLAND PAINTS SDN. BHD. (Co.No.483545-K) Lot 729, 15 ½ Miles, Jalan Sungai Tiram, P.O.Box 46, 81800 Ulu Tiram, Johor Bahru, Malaysia. Tel : 607-861 1555 Fax : 607-861 1777 / 9089

Exterior & Interior Wall

COLOURLAND ELASTOKOTE Product Code: EK – 900 Series Colourland ElastoKote is an exclusive single component waterproof coating which formulated with a special highbuild modified polymer to form a tough, flexible, colored and protective membrane. The cured membrane coating is seamless, durable, UV-resistant and bond strongly to the exposed surfaces, concrete flat roofs and metal surfaces. It can be used as a protective roof coating, coloured coating for sports surfaces or as a trafficable coating system for light to medium traffic areas when used with suitable fibreglass reinforcement material. This product is also highly recommended for used in repairing and renovation project. Usage

It is highly recommended for the application as followed : 1. Floor : Apply under or above screeds to provide a damp proof membrane. 2. Roofs : Apply as the main waterproofing coating or as part of a repair system, it also can be direct applied as protective top coat. 3. Basement : Apply as part of waterproofing system beneath ground level. 4. Walls : Can be used under render/plaster (as water barrier) or applied as a protective top coat. 5. Tiling : As secondary protection under tiles in wet areas e.g. bathrooms and balconies.

Pack Size

5 kg and 20 kg

Performance Specification Tensile Strength

( DIN 53455 )

> 2N / mm2

Elongation at Break

( DIN 53455 )

> 250 %

Adhesion Strength

( ASTM D4541 )

> 1N / mm2

Crack Bridging

( ASTM C836 )

> 2mm (no crack)

Water Vapour Transmission

( ASTM E96 )

Dirt Retention Property

( SS 500 : 2002 )

~ 25-35 g/m2 / 24 hours Before Washing – 95 (Pass: DCI > 92) After Washing – 96 (Pass: DCI > 95)

(Note: To achieve the above specification, the total DFT, dry film thickness must >0.6mm) Composition Pigment

Lightfast Non – Lead Pigments and Mineral Extenders.

Binder

Modified Acrylic Dispersion.

Volume Solids

50%

Thinner / Cleaner

Water.

Properties Texture

Smooth Sheen Finish.

Colour

EK 900 (Dark Grey) and EK 940 (White)

Theoretical Coverage

1.30 kg / m² (0.6 to 0.7mm DFT)

Drying Time

Touch Dry, 1 – 2 Hrs / Hard Dry, 4 Hrs. (Dependent on Temperature and Humidity).

Recoating Interval

4 hours.

Directions for Use Application

Stir well before use. Application can be carried out by using brush, roller or squeegee.

Thinning

Use directly as it is or dilute with a maximum of 10% water.

Cleaning Up

Clean all equipment with clean water immediately after use.

COLOURLAND PAINTS SDN. BHD. (Co.No.483545-K) Lot 729, 15 ½ Miles, Jalan Sungai Tiram, P.O.Box 46, 81800 Ulu Tiram, Johor Bahru, Malaysia. Tel : 607-861 1555 Fax : 607-861 1777 / 9089

Application Instructions All surfaces to be treated must be clean, thoroughly dry and free from all defects or poorly adhering material like dirt, grease and wax. All joints (width: >2mm) shall be sealed with a suitable low modulus, high performance, paintable joint sealant before primed with 1 to 2 coats of Colourland ElastoSeal. For general interior and exterior wall application, it is advised to be painted with 2 coats of Colourland ElastoKote after the priming process. To use Colourland ElastoKote at high stress areas (e.g., internal corners, gaps, outlet cracks, pipe intrusions and etc.), it is advisable to apply together with recommended heavy duty reinforcing material to provide a fully reinforced trafficable system. For membrane application, all the stress points have to be pre-treated follow the above mentioned method. After it, apply Colourland ElastoKote in a uniform coating over the entire area to be waterproofed at about 0.65 kg/m2 by brush, roller or squeegee. Allow to dry for 4 hours. Then apply 2nd coat of Colourland ElastoKote at 0.65 kg/m2 at perpendicular direction to the previous coat and allow drying for a minimum of 24 hours. For maximum protection in substrate susceptible to crack, reinforcing fabric is embedded into the 1st coat during wet and further coated (wet on wet) with the 2nd coat of Colourland ElastoKote . Painting Guide Surface Condition

Primer (To Paint 1 – 2 Coat)

Finish (To Paint 2 Coat)

Powdery Surfaces

Colourland ElastoSeal

Colourland ElastoKote

Alkaline / New Surfaces

Colourland ElastoSeal

Colourland ElastoKote

Sound Surface

Colourland ElastoSeal

Colourland ElastoKote

Previously Painted Surfaces

Colourland ElastoSeal

Colourland ElastoKote

For more information, please visit our website at : www.colourland.com.my . Any advice, recommendations, information, assistance or service provided by Colourland Paints Sdn Bhd in relation to goods manufactured or marketed by it or their use or any application is given in good faith. However, any advice, recommendations, information, assistance or service by Colourland Paints is provided without expressed or implied warranties. Product Technical Data ● Rev 2 ● Sep 2013